Arduino Tutorial: 433Mhz Wireless modules basic setup and example using DHT22 temperature sensor
In this video we are going to build a simple project just to demonstrate how easy it is to add wireless capability to our Arduino Projects with these 433Mhz modules. I have two Arduinos here. This one is sending the temperature and the humidity it measures every two seconds, and the other one is receiving the data and displaying it on the display. As you can see this one way communication is working fine and the range is good, we can easily get around 6 meters with a small antenna! The theoretical range that we can achieve is more than 100 meters. You can find links for all the parts in the description of the video.
Note: This video tutorial is prepared for Greece, where it’s legal to operate low powered devices (25mW) in the 433MHz band without a license. Check what’s legal in your own country.
These 433Mhz modules is a low cost wireless solution for Arduino. This module is the transmitter and this one is the receiver. We can only establish a one way communication link using these two modules. The cost of both modules is less than 2$! The kit operates at the 433MHz band and it can achieve at a data rate of 4Kbits. The connection to Arduino is extremely easy. We only have to connect the DATA pin of the modules to a digital pin on Arduino. But let’s see how to build this project in detail.
WHERE TO BUY
Cheap Arduino Uno: http://bit.ly/Cheap_Arduino_Uno
433Mhz RF Kit: http://bit.ly/433Rf
1.8″ Color TFT: http://bit.ly/Color_TFT_ST7735
Powerbank XIAOMI: http://bit.ly/PowerBank_XIAOMI
First of all, we have to download the VirtualWire library in order to make our life easier when we work with the 433Mhz wireless modules. You can find the link for the library in the description of the video.
Let’s first see the Transmitter code. It sends out a simple data structure which contains two floats, the temperature and the humidity. In order to establish a communication link we have to set which pin we have connected the module to, and set the communication bitrate. In this example I have set the bitrate to 500bps. Next, we read the temperature and the humidity from the sensor, we save the values in the data structure and with this line of code here, we send the data structure. It’s that easy!
Let’s now see the receiver code. Again we declare the same data structure. We initialize the receiver module with the same settings as the transmitter and we wait for data. If there is data available, we save that data in the data structure and then we print that data on the display. It’s that easy! You can find the code of the project in a link in the description of the video.
Virtual Wire: https://www.pjrc.com/teensy/td_libs_VirtualWire.html
Adafruit GFX: https://github.com/adafruit/Adafruit-GFX-Library
Adafruit ST7735: https://github.com/adafruit/Adafruit-ST7735-Library
CODE OF THE PROJECT
QUIZ OF KNOWLEDGE ANDROID GAME
You can download my latest Android Game which is called Quiz of knowledge here:
Arduino Datalogger: https://www.youtube.com/watch?v=oei3Y6tOhVI
Arduino Weather Station Project: https://www.youtube.com/watch?v=9jN-3DtS1RI
Arduino Nokia 5110 LCD Display: https://www.youtube.com/watch?v=aDwrMeu4k9Y
Arduino OLED display tutorial: https://www.youtube.com/watch?v=A9EwJ7M7OsI
DIY Arduino: https://www.youtube.com/watch?v=npc3uzEVvc0
Educ8s.tv is a Youtube channel and website which is dedicated in developing high quality videos about DIY hardware and software projects. In this channel we develop projects with Arduino, Raspberry Pi, we build robots and simple electronic circuits. Check out our website as well for more information: http://www.educ8s.tv
SUBSCRIBE ON YOUTUBE
Never miss a video: Never miss a video: https://www.youtube.com/subscription_center?add_user=educ8s